• Adhesive Targets
• Plastic Targets, to 200 M range
• 2 Point Vector Target
• Rotary Target
• Magnetic Base Target
• CPS12 High Precision Prism
• RT1A High Precision Target

• Single targets, str, 90°, 45°
• Vector Target
• Offset Rods-Extensions
• Hard Point Adapter
• Hard Point Tribrach
• Edge Targe Adapter
• Target Kit

• QHT-1 Tooling Quality Stand
• Wooden Tripod
• Computer Stand

• LA10 Target Illuminator
• DE17 Diagonal Eyepiece
• Carry Case For QHT-1

Adhesive Retro-Reflective Target Sheets

The RS Series Targets are sold in "Sheets"   The number of targets on a sheet varies with the target size.  Normally stocked  sizes are:

RS 10T, 10mm x 10mm, Range; to 20 meters, 400 per sheet     P/N 6345-11

RS 20N, 20mm x 20mm, Range; to 50 meters, 100 per sheet     P/N 6345-20

RS 30N, 30mm x 30mm, Range; to 70 meters, 49 per sheet        P/N 6345-30

RS 50N, 50mm x 50mm, Range; to 80 meters, 16 per sheet        P/N 6345-50

RS 90N, 90mm x 90mm, Range; to 100 meters, 4 per sheet         P/N 6345-90

RS 00, Blank (no pattern), 230mm X 230mm      P/N 6345-00

Plastic Frame Reflective Targets

Plastic Type Target, 4 mounting holes, 1 at each corner, suitable for long distance

RC50, 73mm x 73mm, Range 50 to 120 meters, 7.9 mm thick frame  P/N 6346-05

RC100, 127mm x 127mm, Range 100 to 200 meters, 7.9 mm thick frame  P/N 6346-10

Two Point Vector Target

2RT310A Two Point Target, Magnetic Arm. Suitable for measuring hidden points using the "Offset" routine in the NETrology™ Software.  Observe two targets (as prompted by the software) and the coordinate value is returned at the point of contact.

P/N 6344-03

Also see the "Offset Rods" in the Kinematic Target Accessory Group

Rotary Targets

10mm male screw at the bottom.  Targets rotate 360° about the vertical and horizontal azis.

Sizes available:

RT30G10, 30mm x 30mm, 70 meter range  P/N 6344-13

RT50G10, 50mm x 50mm, 80 meter range  P/N 6344-14

RT90G10, 90mm x 90mm,100 meter range  P/N 6344-15

Magnetic Base Targets

The retro-reflective surface rotates a full  360° about the vertical and horizontal azis on a nagnetic base.  Great for pass- points or temporary bench marks when re-locationg the instrument to a new station.

RT50M, 50mm x 50mm, 80 meter range  P/N 6344-05

RT90M, 90mm x 90mm, 100 meter range  P/N 6344-12

CPS12 HIGH PRECISION PRISM

Tribrach mounting for use on tripods, has optical plummet and tubular level.   Calibration point is at 1kilometer (1000 meters).  Precision, ±2.0 mm + 2ppm X Distance.

Range 50 meters to 100 meters. P/N 6344-04

RT1A High-Precision Target

Tribrach mounting for use on tripods, has optical plummet and tubular level. 

Range 2 meters to 100 meters   P/N 6344-02

Precision, ±0.8 mm to 100 meters

Single Targets:

These Targets are 1144 Steel, Heat treated to RC55 and have a black-oxide finish with the Sokkia Retro-reflectice "zero" prism constant face. 

• Three Configurations, End Viewing (KT6000) Side Viewing, (KT6090 and 45° Face (KT045).
• Typical Male Plug to A.I.A. Standards is 0.2500" (+0.0000, -0.0003) Diameter x 0.50" Long (All Configurations).
• Two Heights are available (above interface), 0.5000" (± 0.0005)( "dash 1") and 0.3125 (± 0.0005)("dash 6")..
• Two "Dot" Sizes are available, 0.010" (up to 4 meters) , and 0.020" (best for sighting up to 15 meters and in areas with vibration).  The "dot" is concentric to the center of the male plug to 0.001" T.I.R.

To Specify: Series-Height-dot Diameter, i.e. KT6000-1-10,  KT6045-6-20                                  

Vector Target:

Two retro-reflective targets, 1.000" apart (1 at 0.2500" and 1 at 1.2500")

Typical Male Plug to A.I.A. Standards is 0.2500" (+0.0000, -0.0003) Diameter x 0.50" Long (All Configurations).

This target is 1144 Steel, Heat treated to RC55 and has a black-oxide finish with the Sokkia Retro-reflectice "zero" prism constant face. 

To Specify: Series-Height-dot Diameter, i.e. KT6290-1-10,  KT6290-1-20                              

Suitable for measuring hidden points using the "Offset" routine in the NETrology™ Software.  Observe two targets (as prompted by the software) and the coordinate value is returned at the point of contact.

Typical Male Plug to A.I.A. Standards is 0.2500" (+0.0000, -0.0003) Diameter x 0.50" Long (All Configurations).Requires HP6000 Hard Point Adapter. Opposite end is female to accept KT6000, KT6090 and KT6045 Targets.

This target is 1144 Steel, Heat treated to RC55 and has a black-oxide finish with the Sokkia Retro-reflectice "zero" prism constant face. Target is offset as indicated

KT6200-1-20, 5.000" Extension 2.5" Target Offset

KT6200-2-20, 11.500" Extension, 4.0 Target Offset

 Offset                                                                    

1.000" Long, x.2500" Female, accepts  all KT series targets and extensions with 0.2500" male plug

Order by HP6000                             

Holds the HP6000 (shown above) 3 each Spherical radius button feet on 2" DIA bolt circle that will position the target or extension normal to an irregular or curved surface.   Useful to develop a point cloud for irregular or spherical surfaces.

Order by HPT6100                                                    

Edge Target Adapter, 1.000" x 0.500" Offset (1" Round stock). Interface is 0.2500" female to accepts all KT series with 0.2500" male plug targets.   Has 8-32 set screw. This adapter is 1144 Steel, Heat treated to RC55 and has a black-oxide finish.

Order by KT6007                                                    

KT6000 Kit includes 2 ea KT6000-1-20, 2 ea KT6045-1-20, 2 ea KT6090-1-20, 1 ea KT6290-1-20, 1 ea KT6200-3-20, 1 ea HP6000, 1 ea HPT6100 and 1 ea KT6007